Vehicles
103 not categorized PORSCHE 930 RED TOPCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.93011019710 This is a paper gasket that sits on top and below the intake manifold flange. Whenever you are servicing the intake manifold or changing the flanges these should be replaced as leaks can cause rough idling and poor drivability. High-quality victor reinz replacement part, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 12 necessary per car. View/Change Diagram
From $3.95
Make a selection 91464110240 Its always nice to know how your engine is running. However, older gauges have a tendency to fail or be out of calibration. Instead of buying a replacement gauge, which can cost hundreds of dollars, we offer a rebuild service that will restore your malfunctioning gauge to as-new condition. Simply send us your malfunctioning gauge with a detailed description of the issue and we will have it rebuilt and sent it back to you in short order. Stop dealing with a broken or non-calibrated gauge in your Porsche! Sold on an exchange basis only; core charge refunded on return of your gauge. View/Change Diagram
From $306.34
Make a selection 91453193910 This fuzzy strip is the easiest to replace of all as it fit right behind the door panel and fits on the top ledge of the door. two required simply remove the door panel to install. View/Change Diagram
From $14.50
Make a selection 91464110120 Its always nice to know how your engine is running. However, older gauges have a tendency to fail or be out of calibration. Instead of buying a replacement gauge, which can cost hundreds of dollars, we offer a rebuild service that will restore your malfunctioning gauge to as-new condition. Simply send us your malfunctioning gauge with a detailed description of the issue and we will have it rebuilt and sent it back to you in short order. Stop dealing with a broken or non-calibrated gauge in your Porsche! View/Change Diagram
$0.01
Make a selection 91456331910 Our brand new reproduction of the lower targa top seal now compliments our upper seal. made from the highest quality weather strip rubber, original seals are now finally failing at an alarming rate. this seal replaces the old original and dramatically increases top sealing, reduces wind noise, and keeps out the weather! easily installed in minutes, you will love the improvement. View/Change Diagram
From $31.27
Make a selection 91464150430 Its always nice to know how your engine is running. However, older gauges have a tendency to fail or be out of calibration. Instead of buying a replacement gauge, which can cost hundreds of dollars, we offer a rebuild service that will restore your malfunctioning gauge to as-new condition. Simply send us your malfunctioning gauge with a detailed description of the issue and we will have it rebuilt and sent it back to you in short order. Stop dealing with a broken or non-calibrated gauge in your Porsche! Clear odometer. Sold on an exchange basis only; core charge refunded on return of your gauge. (black needle hub) View/Change Diagram
$390.00
Make a selection 91464130212 Its always nice to know how your engine is running. However, older gauges have a tendency to fail or be out of calibration. Instead of buying a replacement gauge, which can cost hundreds of dollars, we offer a rebuild service that will restore your malfunctioning gauge to as-new condition. Simply send us your malfunctioning gauge with a detailed description of the issue and we will have it rebuilt and sent it back to you in short order. Stop dealing with a broken or non-calibrated gauge in your Porsche! Sold on an exchange basis only; core charge refunded on return of your gauge. Core must be in good shape not damaged and able to be rebuilt to receive a refund. These are made to order please call to inquire abo...(choose a part on the right to read more) View/Change Diagram
From $201.25
Make a selection 91464150530 Its always nice to know how your engine is running. However, older gauges have a tendency to fail or be out of calibration. Instead of buying a replacement gauge, which can cost hundreds of dollars, we offer a rebuild service that will restore your malfunctioning gauge to as-new condition. Simply send us your malfunctioning gauge with a detailed description of the issue and we will have it rebuilt and sent it back to you in short order. Stop dealing with a broken or non-calibrated gauge in your Porsche! Clear odometer. Sold on an exchange basis only; core charge refunded on return of your gauge. Gauge has silver needle button. View/Change Diagram
$390.00
Make a selection 91464130110 Its always nice to know how your engine is running. However, older gauges have a tendency to fail or be out of calibration. Instead of buying a replacement gauge, which can cost hundreds of dollars, we offer a rebuild service that will restore your malfunctioning gauge to as-new condition. Simply send us your malfunctioning gauge with a detailed description of the issue and we will have it rebuilt and sent it back to you in short order. Stop dealing with a broken or non-calibrated gauge in your Porsche! View/Change Diagram
From $747.50
Make a selection 95037003 Stoptech brake lines consist of a ptfe (commonly referred to as teflon) inner line that carries the brake fluid, which is then covered with a layer of stainless steel woven braid. The ptfe tube is very resistant to expansion under pressure and will not degrade from exposure to brake fluid. every stoptech brake line is 100% tested in-house to a pressure of 4,500 psi. This is almost 4 times the typical line pressure exerted by a production vehicle's master cylinder. stoptech is a registered brake line manufacturer with the united states DOT and all stoptech stainless steel brake lines are manufactured to meet DOT compliance standards. Stoptech stainless steel lines also meet or exceed fmvss 106 and applicable...(choose a part on the right to read more) General Fitment911 1965-69911 1970-73 911 1974-77 911 1978-83 911 1984-86 912 1965-69
$91.60
Make a selection 93060201501 Complete distributor without an exchange. This distributor has been completely remanufactured, which includes a full inspection, disassembly, cleaning and degreasing. We then install a toothed timing belt, 3 German made top bearings, 1 German made lower bearing and a distributor pinion pin (part # 930 602 922 00). We also install new dust caps, Bosch rotors and Bosch cap. Clearances, timing and proper operation are then checked to ensure reliability.
$2,534.40
Make a selection 930602015AX3ATK Send us your distributor and we will remanufacture it for you. A perfect option for those who have time and want to save on costs. The remanufacturing process includes full inspection, disassembly, cleaning and degreasing. We then install a toothed timing belt, 3 German made top bearings, 1 German made lower bearing and a distributor pinion pin (part # 930 602 922 00). Clearances, timing and proper operation are then checked to ensure reliability. Please note: each distributor is remanufactured in Germany, so the lead times can vary.
$1,393.04
Make a selection 94456443001 If your late 1986 and newer 944 and 924s sunroof has stopped working but you can still hear the motor running, the sunroof gears have probably stripped because the tension in the motor cable is too tight. easily replaced with the headliner pad removed, simply relax the tension of the cable at the sunroof motor and never suffer again! two required. View/Change Diagram
$12.09
Make a selection 91179950307 This seal sits on the trailing edge of the front fender at the top just below the windshield. Sold individually. 2 necessary per car. Driver's or passengers side fitment. View/Change Diagram
From $6.29
Make a selection 95037008 Stoptech brake lines consist of a ptfe (commonly referred to as teflon) inner line that carries the brake fluid, which is then covered with a layer of stainless steel woven braid. The ptfe tube is very resistant to expansion under pressure and will not degrade from exposure to brake fluid. every stoptech brake line is 100% tested in-house to a pressure of 4,500 psi. This is almost 4 times the typical line pressure exerted by a production vehicle's master cylinder. stoptech is a registered brake line manufacturer with the united states DOT and all stoptech stainless steel brake lines are manufactured to meet DOT compliance standards. Stoptech stainless steel lines also meet or exceed fmvss 106 and applicable...(choose a part on the right to read more) General Fitment944 1989-91968 1992-95
$126.83
Make a selection 95037014 Stoptech brake lines consist of a ptfe (commonly referred to as teflon) inner line that carries the brake fluid, which is then covered with a layer of stainless steel woven braid. The ptfe tube is very resistant to expansion under pressure and will not degrade from exposure to brake fluid. every stoptech brake line is 100% tested in-house to a pressure of 4,500 psi. This is almost 4 times the typical line pressure exerted by a production vehicle's master cylinder. stoptech is a registered brake line manufacturer with the united states DOT and all stoptech stainless steel brake lines are manufactured to meet DOT compliance standards. Stoptech stainless steel lines also meet or exceed fmvss 106 and applicable...(choose a part on the right to read more) General Fitment911 1998-05911 2005-08
$63.42
Make a selection 95037502 Stoptech brake lines consist of a ptfe (commonly referred to as teflon) inner line that carries the brake fluid, which is then covered with a layer of stainless steel woven braid. The ptfe tube is very resistant to expansion under pressure and will not degrade from exposure to brake fluid. every stoptech brake line is 100% tested in-house to a pressure of 4,500 psi. This is almost 4 times the typical line pressure exerted by a production vehicle's master cylinder. stoptech is a registered brake line manufacturer with the united states DOT and all stoptech stainless steel brake lines are manufactured to meet DOT compliance standards. Stoptech stainless steel lines also meet or exceed fmvss 106 and applicable...(choose a part on the right to read more) General Fitment911 1989-94911 1994-98
$91.60
Make a selection 95037504 Stoptech brake lines consist of a ptfe (commonly referred to as teflon) inner line that carries the brake fluid, which is then covered with a layer of stainless steel woven braid. The ptfe tube is very resistant to expansion under pressure and will not degrade from exposure to brake fluid. every stoptech brake line is 100% tested in-house to a pressure of 4,500 psi. This is almost 4 times the typical line pressure exerted by a production vehicle's master cylinder. stoptech is a registered brake line manufacturer with the united states DOT and all stoptech stainless steel brake lines are manufactured to meet DOT compliance standards. Stoptech stainless steel lines also meet or exceed fmvss 106 and applicable...(choose a part on the right to read more) General Fitment911 1989-94
$63.42
Make a selection 96274 The 996 turbo 74mm competition plenum is designed to function with more seriously modified turbos developing over 600+ horsepower. Although this 74mm application has been used with great success on a variety of turbos ranging from mildly modified to 1000+ hp. This application requires the larger 74mm Porsche throttle body (additional purchase required) and comes with additional hardware to complete the kit. This competition turbo plenum will help modified 996 turbos achieve maximum engine performance. General Fitment911 TURBO/GT2 2001-05
$1,343.25
Make a selection 911561189668VB This driver's side top seal can degrade with time and is essential to keep moisture out of the cabin. We recommend replacing the right and left sides together. The passenger's side is part # 911561190668vb sold individually. Driver's side fitment. View/Change Diagram
From $158.27
Make a selection 96434350301 This is the lower strut plate that retains the spring and sits on top of the adjusting nut. We recommend that you inspect and replace if necessary with any new shock install. This plate tends to suffer from corrosion as debris collects in it with time. Sold individually. Right or left side fitment. 2 necessary per car.
From $39.00
Make a selection 96435104102EQ If you are experiencing a pulsation and hearing grinding sounds when braking, odds are your rotors need to be replaced to restore full stopping power. This rotor is an OEM replacement, manufactured by zimmermann in Germany. It is internally vented and z-coated for corrosion resistance. Sold individually - left or right side fitment
$170.50
Make a selection 96437505502 Are you experiencing vibrations in the cabin? The most likely cause is a worn transmission mount. Severely worn mounts translate to engine component wear and can even cause difficulty shifting. Our mount is manufactured in europe by an OEM supplier using the finest materials. Be sure to swap yours out during your next service. Sold individually. Central fitment in transmission carrier. 1 qty. Required per carrier. Tech tip: the bushing should be mounted with the 2 openings on the vertical plane. Now is the time to replace the old hardware as well. Below is a list of what is needed for installation. 964 1 qty. Hex head bolt m12x1.5x95 90037802702 1 qty. Lock nut m12x1.5 49020001 2 qty. Stop washers 96437525500 9...(choose a part on the right to read more) View/Change Diagram
From $165.00
Make a selection 964565035017EQ This is genuine targa top material sourced from Germany. It is as close to the original as possible and is cut and trimmed to fit perfectly. We also make sure that there is plenty of material to stretch out the sides so that there are no wrinkles when installed. Sold individually. 1 necessary per car.
$335.50
Make a selection 970BBKIT10 Vivid racing chooses wald international aerodynamic parts for their top class products designed to improve the appearance and performance of your vehicle. The quality, fitment and design of wald are unmatched in the industry. Constructed of carbon fiber, wald aero kits are both light weight and durable. General FitmentPANAMERA 2010-14
$28,939.95
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |